Accton-technology CheetahAccess Wireless Gateway AC-IG2004W Manual de usuario

CheetahAccessTM Wireless GatewayAC-IG2004WUser Guide

Introduction1-2• Supports PPP dial-in connection using standard dial-up program• Easy setup through a Web browser on any operating system that support

Applications1-3•SecurityThe CheetahAccess Wireless Gateway supports security features that can deny Internet access to specified users, or filter all

Introduction1-4

2-1Chapter 2: InstallationBefore installing the CheetahAccess™ Wireless Gateway, verify that you have all the items listed under “Package Contents.” I

Installation2-2Although access speed to the Internet is determined by the modem type connected to your CheetahAccess Wireless Gateway, data passing be

Description of Hardware2-3• Three RJ-45 ports for connection to a 10BASE-T/100BASE-TX Ethernet Local Area Network (LAN). These ports can auto- negotia

Installation2-4System RequirementsYou must have an Internet Service Provider (ISP) that meets the following minimum requirements:• Internet access fro

Connect the System2-5Prepare a serial cable for connecting the CheetahAccess Wireless Gateway to an ISDN TA or PSTN modem.3. Connect your printer: Use

Installation2-6Warning: Do not plug a phone jack connector into any RJ-45 port. This may damage the CheetahAccess Wireless Gateway. Instead, use only

Connect the System2-7CheetahAccess Wireless Gateway. A wireless infrastructure can be used for access to a central database, or for connection between

Installation2-8Note: When connecting to the WAN port, use 100-ohm Category 3, 4 or 5 shielded or unshielded twisted-pair cable with RJ-45 connectors a

3-1Chapter 3: Configuring Client PCsTCP/IP ConfigurationTo access the Internet through the CheetahAccess™ Wireless Gateway, you must configure the net

Configuring Client PCs3-2

4-1Chapter 4: Configuring the CheetahAccess™ Wireless GatewayAfter you have configured TCP/IP on a client computer, you can use a Web browser to confi

Configuring the CheetahAccess™ Wireless Gateway4-2Setting a PasswordIf this is your first time to access the CheetahAccess Wireless Gateway, you shoul

Main Menu4-3Status Menu Displays connection status, key interface settings, as well as the firmware and hardware version numbers.INTERNET Displays WAN

Configuring the CheetahAccess™ Wireless Gateway4-4Networking and Client ServicesUse the Setup menu to configure the LAN interface (including TCP/IP pa

Networking and Client Services4-5Use this menu to restrict management access based on a specific password. You must enter a password to access the con

Configuring the CheetahAccess™ Wireless Gateway4-6Valid IP addresses consist of four numbers separated by periods. The first three fields are the netw

Networking and Client Services4-7Dynamic IP Address – DHCPThe Host Name is optional, but may be required by some ISPs. The default MAC address is set

User GuideCheetahAccessTM Wireless Gateway10/100 Mbps Wireless Gateway with 3 10/100 Mbps (RJ-45) Ethernet LAN ports,and 1 10Mbps (RJ-45) WAN Port

Configuring the CheetahAccess™ Wireless Gateway4-8PPP over Ethernet – PPPoEEnter the PPPoE user name and password assigned by your ISP. The Service Na

Networking and Client Services4-9Check if you only use a dial-up modem to connect to the Internet. – If the serial port is used for primary Internet a

Configuring the CheetahAccess™ Wireless Gateway4-10Wireless ConfigurationTo configure the CheetahAccess Wireless Gateway as a wireless access point fo

Networking and Client Services4-11However, please be aware that the extra processing time required for encryption may affect the throughput for wirele

Configuring the CheetahAccess™ Wireless Gateway4-12Configuring Client ServicesThe CheetahAccess Wireless Gateway includes a broad range of client serv

Networking and Client Services4-13Virtual ServerIf you configure the CheetahAccess Wireless Gateway as a virtual server, remote users accessing servic

Configuring the CheetahAccess™ Wireless Gateway4-14Enabling Special ApplicationsSome applications (such as Internet gaming, videoconferencing, Interne

Networking and Client Services4-15Client FilteringYou can filter Internet access for local clients based on IP address, application type (i.e., HTTP p

Configuring the CheetahAccess™ Wireless Gateway4-16MAC FilteringYou can filter Internet access for local wired and wireless clients based on MAC addre

Networking and Client Services4-17Association Control: The Association process is the exchange of information between wireless clients and a wireless

Accton is a trademark of Accton Technology Corporation. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of t

Configuring the CheetahAccess™ Wireless Gateway4-18Miscellaneous SettingsThe CheetahAccess Wireless Gateway also allows you set a timeout for administ

Viewing Network and Device Status4-19Viewing Network and Device StatusYou can use the following screen to display the connection status for the WAN/WL

Configuring the CheetahAccess™ Wireless Gateway4-20Using System ToolsYou can use the “Tools” menu to reboot the CheetahAccess Wireless Gateway, restor

5-1Chapter 5: Configuring Client TCP/IPIf you have not previously installed the TCP/IP protocol on your client PCs, refer to the following section. If

Configuring Client TCP/IP5-25. Select the “Microsoft” item in the manufacturers list. And choose “TCP/IP” in the Network Protocols. Click the “OK” but

Setting TCP/IP to Work with the CheetahAccess™ Wireless Gateway5-34. You can dynamically assign TCP/IP address settings to a client, or you can manual

Configuring Client TCP/IP5-4Manual IP Configuration1. Select “Specify an IP address” in the “IP Address” tab. Select an IP address based on the defaul

Setting TCP/IP to Work with the CheetahAccess™ Wireless Gateway5-5Verifying Your TCP/IP ConnectionAfter installing the TCP/IP communication protocol a

Configuring Client TCP/IP5-6

6-1Chapter 6: Configuring Printer ServicesIf you want to use the print server built into the CheetahAccess™ Wireless Gateway, then you must first inst

Limited WarrantyAccton Technology CorporationLimited Warranty: Accton warrants all is products to be free of manufacturing defects in workmanship and

Configuring Printer Services6-22. Select the destination folder and click on the “Next” button. The setup program will then begin to install the progr

Install the Printer Port Monitor6-34. Enter the printer port name that will be used to identify the port monitor in your system, and press “Next.”5. W

Configuring Printer Services6-4Configure the Print ServerThe CheetahAccess Wireless Gateway’s print server supports Microsoft Windows 95/98/ME/NT/2000

Configure the Print Server6-53. Specify the printer type attached to the CheetahAccess Wireless Gateway, and press “Next.”4. From the list of manufact

Configuring Printer Services6-65. Continue following the prompts to finish installing the CheetahAccess Wireless Gateway print server. The printer typ

Configure the Print Server6-78. Select the “Ports” tab in the Properties window.9. Select the monitored port (the default port name is “AC-IG2004W”) a

Configuring Printer Services6-8Configure the Network Printer in Windows NT1. On a Windows NT platform, open the Printers window in the My Computer men

Configure the Print Server6-94. Enter the IP address of the CheetahAccess Wireless Gateway and click “OK,” and then click “Next” in the Add Printer Wi

Configuring Printer Services6-10

A-1Appendix A: TroubleshootingThis appendix describes common problems you may encounter and possible solutions. The CheetahAccess™ Wireless Gateway ca

Limited WarrantyWARRANTIES EXCLUSIVE: IF AN ACCTON PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR REPLACE

TroubleshootingA-2Network Connection ProblemsCannot ping the CheetahAccess Wireless Gateway from the attached LAN, or the CheetahAccess Wireless Gatew

B-1Appendix B: CablesEthernet CableSpecificationsTwisted-pair CableCaution: DO-NOT plug a phone jack connector into any RJ-45 port. Use only twisted-p

CablesB-2Straight-through CableCrossover CableRJ-45 Port Pin AssignmentsAll LAN ports on the CheetahAccess Wireless Gateway support automatic MDI/MDI-

Serial Port Pin AssignmentsB-3Serial Port Pin AssignmentsThe DB-9 serial port on the rear panel is used to connect the CheetahAccess Wireless Gateway

CablesB-4Serial Port to 9-Pin COM Port on PCSerial Port to 25-Pin DCE Port on ModemSerial Port to 25-Pin DTE Port on PCGateway’s 9-Pin Serial Port CCI

Printer Port Pin AssignmentsB-5Printer Port Pin AssignmentsThe DB-25 parallel port on the CheetahAccess Wireless Gateway’s rear panel is used to conne

CablesB-6

C-1Appendix C: SpecificationsWAN Interface10BASE-T, 1 RJ-45 portSerial, 1 RS-232 DB-9 connectorLAN Interface10BASE-T/100BASE-TX3 RJ-45 portsWLAN Inter

SpecificationsC-2Management Web managementAdvanced FeaturesDynamic IP Address Configuration – DHCP, DNSFirewall – Client privileges, hacker prevention

C-3C-Tick - AS/NZS 3548 (1995) Class BETS 300 328MPT RCR STD-33EN 61000-3-2/3ImmunityEN 61000-4-2/3/4/5/6/8/11SafetyUL 1950EN60950 (TÜV)CSA 22.2 No. 9

ContentsiContentsChapter 1: Introduction 1-1About the CheetahAccess™ Wireless Gateway 1-1Features and Benefits 1-1Applications 1-2Chapter 2: Install

SpecificationsC-4

D-1Appendix D: Ordering InformationCheetahAccess™ Internet Gateway ProductsAC-IG1004 4-port Internet Gateway - WAN/LAN/Print ServerAC-IG1008 8-port In

Ordering InformationD-2

AC-IG2004WE102001-R01Part Number: 650.10511

ContentsiiVirtual Server 4-13Enabling Special Applications 4-14Client Filtering 4-15MAC Filtering 4-16Miscellaneous Settings 4-18Viewing Network

1-1Chapter 1: IntroductionCongratulations on your purchase of the CheetahAccess™ Wireless Gateway. Accton is proud to provide you with a powerful yet